Cisco switches can be used as plug-and-play devices out of the box but they also offer an enormous amount of features. Although the main purpose of the switch is to provide inter-connectivity in Layer 2 for the connected devices of the network, there are myriad features and functionalities that can be configured on Cisco Switches.

• Cisco Binary Game
• Cisco Binary Game Cheats Age Of Empires 2

In the following Cisco Switch Commands Cheat Sheet, I have tried to include the most important and frequently-used CLI commands that Cisco professionals encounter in real world networks. I know that the list is not exhaustive but I believe that the most useful commands are included. Make sure to download the whole commands cheat sheet in PDF format below so you can print it or save it on your computer for future reference.

NOTE: Other Cisco Command Cheat Sheet Posts:

The following commands will work on most Cisco switch models such as 4500, 3850, 3650, 2960, 3560 etc.

The Binary Game Instructions: If you see a binary number, enter the decimal value in the green box. If you see a decimal number on the right, click the bits to make the binary number match. This game is an adaptation of the Binary Game from Cisco Systems Page Visits. Cisco Command Cheat Sheet. In this Cisco Command Cheat Sheet age, you find the most used Cisco commands in real world. You will both learn new commands and recall the Cisco commands that you have already know. Here, you will not only learn Cisco commmands but also you will find the Juniper, Nokia and Huawei equivalent of these Cisco commands on Cisco Command Cheat Sheet.

Verification Commands:

TestSwitch#show version

[Displays software and hardware information]

TestSwitch#show running-config

[Displays currently running configuration in DRAM]

TestSwitch#show start

[Displays configuration in NVRAM which will be loaded after reboot]

TestSwitch#show flash:

[Displays Flash memory information]

TestSwitch#show boot

[Displays boot path and image]

TestSwitch#show clock

[Displays the system clock]

TestSwitch#show interfaces

[Displays all interfaces configuration and status of line]

TestSwitch#show vlan

[Displays vlan number, name, status and ports associated with it]

TestSwitch#show vtp status

[Displays VTP mode, Number of existing vlans and config revision]

TestSwitch#show interface status

[Displays interface status, vlan, Duplex, Speed and type]

TestSwitch#show etherchannel

[Displays etherchannel information]

TestSwitch#show cdp neighbors

[Displays information of connected devices]

TestSwitch#show cdp neighbors detail

[Displays detailed information of connected devices]

TestSwitch#show mac address-table

[Displays current MAC address forwarding table and which MAC is learned on each switch port]

Cisco Binary Game

TestSwitch#show spanning-tree

[Displays spanning-tree state information, which interfaces are in active or blocking state etc]

Resetting the Switch

TestSwitch#delete flash:vlan.dat

[Deletes vlan database from flash memory so you can start adding new VLANs from scratch]

TestSwitch#erase startup-config

[Delete start-up file from NVRAM]

TestSwitch#reload

[Reboot the Switch]

Setting Host Names

TestSwitch#config t

[Entering into Global Configuration Mode]

TestSwitch(config)#hostname MySwitch

[Enter the hostname of the switch]

MySwitch(config)#

Setting login credentials:

MySwitch(config)#username admin password csico1234

[create username and password for logging in to the switch]

MySwitch(config)#enable secret test1

[Sets encrypted secret password using MD5 algorithm. This is the enable password that you will be asked to enter when trying to enter into “enable” mode]

MySwitch(config)#service password-encryption

[Encrypt all the passwords using MD5]

Console Access:

MySwitch(config)#line con 0

[Enter into line console mode]

MySwitch(config-line)#password test3

[Set password on console]

MySwitch(config-line)#login

[Enable password checking on console]

SSH/Telnet Access to the switch:

MySwitch(config)#line vty 0 4

[Enters line vty mode for all five virtual ports]

MySwitch(config-line)#transport input ssh

[Enable SSH]

Browse by PC Games Title: Hints and Tips for:Pokemon Trading Card Game Online CheatsPokemon Trading Card Game OnlineCheat Codes:-Submitted by: David K.Pokemon EX hat:-Enter dragonsexalted, darkexplorers, or nextdestinies as a redemption code.Theme deck:-Enter plasmafreeze, plasmablast, plasmastorm, or boundariescrossedas a redemption code.Submit your codes! Pokemon trading card game cheat codes. Having Codes, cheat, hints, tips, trainer or tricks we dont have yet?Help out other players on the PC by adding a cheat or secret that you know!SubmitVisit Cheatinfo for moreSpotlight - New Version CheatBook DataBase 2020Cheatbook-Database 2020 is a freeware cheat code tracker that makes hints, Tricks, Tips and cheats (for PC, Walkthroughs,XBox, Playstation 1 and 2, Playstation 3, Playstation 4, Sega, Nintendo 64, Wii U,DVD, Game Boy Advance, iPhone, Game Boy Color, N-Gage, Nintendo DS, PSP, Gamecube, Dreamcast, Xbox 360, Super Nintendo) easily accessible from one central location.

MySwitch(config-line)#transport input telnet

[Enable telnet]

MySwitch(configiline)#password test3

[Set password]

Setting IP Address (To allow remote access to the switch):

MySwitch(config)#interface vlan1

[Enters vlan1, the native vlan]

MySwitch(config-if)#ip address 192.168.1.2 255.255.255.0

[Set IP address for management]

MySwitch(config-if)#exit

MySwitch(config)#ip default-gateway 192.168.1.1

[Exit path for the switch – gateway IP]

Interface description

MySwitch(config)#interface g0/1

MySwitch(config-if)#description TO SERVER

Duplex and Speed Settings

MySwitch(config)#interface g0/1

MySwitch(config-if)#speed 10

[Force 10Mbps Speed]

MySwitch(config-if)#speed 100

[Force 100Mbps Speed]

MySwitch(config-if)#speed auto

[Enable auto speed configuration]

MySwitch(config-if)#duplex auto

[Enable auto duplex configuration on switch port]

MySwitch(config-if)#duplex full

[Enable full duplex configuration on switch port]

MySwitch(config-if)#duplex half

[Enable half duplex configuration on switch port]

Setting Web-based interface for configuration (GUI):

MySwitch(config)#ip http server

Cheats on how to create 'baba yaga'. Contains all of possible combinations. You need to have parent items discovered to succeed. Baba yaga game cheats. How to cheats steps that will guide you to creation of baba yaga from starting items. Water + air = mist. Earth + earth = land. Land + land = continent. Continent + continent = planet. Air + planet = atmosphere. Atmosphere + mist = cloud. Little Alchemy 2 Official Cheats Little Alchemy 2 game.

[Enable HTTP server]

MySwitch(config)#ip http port 80

[Set port number for HTTP]

Port-Security

MySwitch(config)#interface g0/1

[Enter the interface to set port-security]

MySwitch(config-if)#switchport port-security

[Enable port security on the interface]

MySwitch(config-if)#switchport port-security mac-address sticky

[Interface converts all MAC addresses to sticky secure addresses]

MySwitch(config-if)#switchport port-security maximum 1

[Only one MAC address will be allowed for this port]

MySwitch(config-if)#switchport port-security violation shutdown

[Port will shut down if violation occurs]

MySwitch(config-if)#exit

MySwitch(config)#exit

MySwitch#show port-security

[Verifying Port security]

Save current configuration

MySwitch(config)#copy running-config startup-config

PortFast

“Portfast” bypasses the Spanning Tree states and brings the port up as quickly as possible. Use it only if you connect a regular host (e.g Computer) on the port. Do not use this command when the port is trunk or if you connect other switches on the specific port.

MySwitch(config)#interface FastEthernet 0/1

MySwitch(config-if)#spanning-tree portfast

Configuring VLANs

MySwitch(config)#vlan 20

[Create a Layer2 VLAN with id 20]

MySwitch(config-vlan)# name testvlan

[Enter a name for the vlan]

MySwitch(config-vlan)#exit

MySwitch(config)#exit

MySwitch#show vlan brief

[Verify the vlan database]

Assigning access ports to a vlan

MySwitch(config)#interface g0/1

MySwitch(config-if)#switchport mode access

[Set the interface in switch access mode]

MySwitch(config-if)#switchport access vlan 20

[Assign the port to vlan 20]

MySwitch(config-if)#exit

The following commands will select a range of interfaces (from 1 to 24) and add all of them to vlan20

MySwitch(config)#interface range gigabitEthernet 0/1-24

MySwitch(config-if)#switchport mode access

MySwitch(config-if)#switchport access vlan 20

MySwitch(config-if)#exit

Configuring trunk port

MySwitch(config)#interface g0/2

MySwitch(config-if)#switchport trunk encapsulation dot1q

[Configure the port to support 802.1Q Encapsulation (default is negotiate)]

MySwitch(config-if)#switchport mode trunk

[Set the interface in permanent trunking mode]

MySwitch(config-if)#switchport trunk native vlan 20

[Specify native vlan for 802.1q trunks – OPTIONAL]

MySwitch(config-if)#switchport trunk allowed vlan 2-5

[vlans 2 to 5 are allowed to pass through the trunk]

MySwitch(config-if)#switchport trunk allowed vlan add 7

[add also vlan 7 in the allowed vlans]

MySwitch(config-if)#switchport trunk allowed vlan remove 3

[remove vlan 3 from the allowed vlans in the trunk]

MySwitch#show interface g0/2 trunk

[Verify the trunk ports and associated vlans on the specific interface]

DOWNLOAD THE CHEAT SHEET AS PDF FILE

As a security feature, Cisco IOS® Software separates EXEC sessions into two different access levels: user EXEC level and privileged EXEC level. User EXEC level allows you to access only basic monitoring commands; privileged EXEC level allows you to access all router commands. Privileged EXEC level can be password protected to allow only authorized users the ability to configure or manage the router. From privileged EXEC level, you can access all the command modes. There are five command modes: global configuration mode, interface configuration mode, subinterface configuration mode, router configuration mode, and line configuration mode.

After an EXEC session is established, commands within Cisco IOS Software are hierarchically structured. Understanding this hierarchy is important for successfully configuring a router. The following figure illustrates a simple high-level schematic diagram of some Cisco IOS commands. This figure summarizes the different modes you will explore in the Interface Labs in a later section.

Command options and applications vary, depending on your position within this hierarchy. Configuration command options are not available until you have navigated to the configuration branch of the Cisco IOS command-line interface (CLI) structure. When you are in the configuration branch, you may enter system-level configuration commands that apply to the entire router at the global configuration level. Interface-specific configuration commands are available when you switch to the interface configuration level. More detailed information and examples of how to navigate through the Cisco IOS CLI hierarchy are offered in the router configuration labs that follow in a later section of this module.

To assist you in navigation through the Cisco IOS CLI, the command prompt changes to reflect your position within the command hierarchy. This setup allows you to easily identify where within the command structure you are at any given moment. The following table is a summary of command prompts and the corresponding location within the command structure.

Now that you are familiar with all the router modes, go to Lab: Navigating the Cisco IOS Architecture.